In the course of my day job, we recently acquired a 360-degree camera. I was fortunate enough to use this device to take some pics of the OKC container home in 360 degrees. Take the OKC container home 360 tour below by clicking the play button on each image and then using the mouse to navigate each immersive space. For those of you with VR headsets, you can click the three dots in the upper right of each image and activate VR mode, then use your camera and headset to view each area as if you were there:
During the entirety of this project, there haven’t been too many things that constitute a “disaster.” In reality, the following tale of a burst pipe that flooded the container overnight doesn’t really a disaster make, but it was a frightening episode that caused more than a little inconvenience.
So, as I mentioned in the kitchen post, the Heatworks1 instant hot water heater was mounted under the sink. After the sink went in, the unit was flushed and activated according to the manual, and it surely did make hot water in an instant. Everything seemed to be working fine.
Well, a few days after the kitchen had been finalized, I showed up to the container one day and noticed a giant puddle out front as I pulled up. “Did it rain last night?” I thought to myself. Upon opening the door, it looked like it had rained INSIDE the container, because there was a discernible layer of water covering everything that had been on the floor.
For a while, I couldn’t figure out what had happened, but then I opened the kitchen sink cabinet and noticed all the pipes under there were wet. I called the plumbers, and they were able to point out the problem fairly quickly: A piece of PEX tubing installed as part of the outlet line of the Heatworks1 had exploded somehow. The plumbers noted this was highly unusual, as PEX tubing is ultra-durable. While it may give way to hairline cracks and pinholes in a line, the plumbers say they had never seen a piece of PEX fail in the violent manner in which mine did.
So, they went about replacing the burst PEX line, but it became clear that the HEATWORKS1 had developed a leak on its inlet valve, on the bottom of the unit. It would just have to remain off until the manufacturer, whom I also contacted that morning, sends a replacement, which they seemed happy and willing to do after I jump through a few hoops online.
Later that day, a neighbor came by to tell me he had noticed the container leaking from the drain valve that leads out the bottom of the kitchen floor to the outside, thereby creating the puddle seen in the photo above. He was kind enough to shut off the water main at the meter box near the street (I think he’s actually a plumber, too).
Anyway, it was very relieving and heartwarming to know I’ll soon be living in a place with great and considerate neighbors such as that.
Pretty much concurrent with the work for the shower, work progressed on the kitchen as well. The base cabinets had already been installed, but I still needed a counter top, a sink to go in it, a fridge, a pantry and a hanging cupboard.
For the base cabinets, I chose a stain color called driftwood from Home Depot and applied it using a brush, then further textured the stain by running a ragged piece of plastic over the freshly applied coat of stain. The end result creates striations throughout the stained surfaces (hard to see in pic; I need to get close-ups…).
I honestly don’t do a lot of cooking, and so I don’t have a lot of cooking supplies, flatware and related kitchen trappings. I only have two bowls, four plates, four forks, spoons and knives, two tall glasses, two short glasses, four shot glasses, one metal pot and one small frying pan. Between the base cabinets and this hanging cupboard, I should have more than enough space for my current kitchen plus the counter top appliances (burner, toaster over, coffee machine) that I’ll eventually want to get.
In the interest of saving on material waste and also conserving a few dollars in the process, I went to Builders Warehouse in search of a remnant to use as my kitchen counter top. They have a kinda weird policy where if you buy a full new slab from the, they won’t do any fabrication on it (won’t cut holes, trim to fit or polish). If you buy a remnant, however, they will do whatever you want. So I was in luck when I found a remnant that was barely over the dimensions I needed. I also selected a shallow sink designed for an RV and, with sink and granite remnant in their hands, they trimmed it to fit, cut out the required hole and polished the raw edges after about a week after items were purchased.
We lifted the heavy granite remnant into place and admired my new kitchen counter top. It would remain clamped overnight to encourage the bonding process. Going the remnant route definitely has its advantages with regard to the fabrication of a counter top that fits your needs, but it also helps if one isn’t too picky about the color or style of the granite, because finding a remnant that meets both practical and aesthetic constraints for a job would be quite difficult, I imagine. So, I wasn’t too picky going into my remnant hunt; I just wanted something close to the size I needed. Waste not, want not.
Now that we had a counter top, I could call the plumbers and have them install the kitchen sink up to code specifications. Of course, I had fired the original plumbers, but the tile guy had a recommendation that worked out really well: E3B Plumbing (inexplicably, I CANNOT find a link for these guys, so maybe I have the name wrong … ?). These guys have a central dispatch and uniforms, which speaks to their size and professionalism. They sent out two plumbers to install my sink on the same day I contacted them, and those guys were finished in about two hours.
And so, with the addition of a faucet, fridge and pantry unit, the kitchen really kinda came together all at once. The fridge I chose was a Danby apartment-sized fridge, which is Energy Star-rated and matched the look and feel of other design elements of the container. It works really well and is very quiet.